Hey Mike,
When measuring for an RV Cover you'll want to measure from the end of the rear bumper to front of the trailer body, without including the trailer tongue. If your trailer measures 24' to 26' in length then you'll want to go with the Adco Olefin HD RV Cover # AD77ZR. Based on the picture I doubt it's smaller but if it's less than 24' you can go with the # AD67ZR (22' - 24') instead.
The Adco Olefin HD line is rated for use in all climates and comes with an white Olefin top panel... view full answer...
Hi Shelly, thanks for the question and it's possible we have something depending on the dimensions of your skylight/sunroof. What most people use for this is the Camco Lights Out Retractable Shade for RV Roof Vents # CAM42913.
Technically it's to cover up vents, but could work for you as when fully extended it measures 19" long x 14-1/8"wide.
You asked about a pillow, and there is one, but again it's for vents is smaller than the aforementioned retractable shade. For a 14" x 14" pillow... view full answer...
The dimensions for the trim plates included with the RV Propane Gas Detector # RS64FR are taken at the longest and widest points of each cover so the larger bracket is 7-1/4" long and 3-3/8" wide at the furthest points. The same for the size of the smaller bracket at 5-3/4" long and 4-1/4" wide. view full answer...
Hello Jason. I can definitely point you in the right direction. I was not able to find any references for the Model 6250c907 that would tell me exactly what cover you need, but I can provide dimensions for the covers you mentioned.
The Replacement RV Air Conditioner Cover for MaxxAir Units - Coleman-Mach / RVP Brand # MA8335A5261 measures 37" long, 25" wide, and 13-1/2" tall.
We also have the Replacement RV Air Conditioner Cover for MaxxAir TuffMaxx Units - Coleman-Mach - White # MA00-325001... view full answer...
The Adco Olefin HD RV Cover # AD27ZR has 3 separate sections on the passenger side which can be opened to access the front or rear door on your 2023 Coleman Light 2715RL. I see you were looking at the larger Cover # AD59ZR but this is going to be too long for your Coleman since the overall length of your camper is 31.92' and the dimensions listed are for the box only. view full answer...
Hi Craig,
RV city water inlets are typically all the same size but the mounting style and flange size can vary so you'll want to measure the current flange to determine if the # 372160-85-A-26A's 3" flange diameter will be enough to cover the cutout hole. Recessed mounts typically require a bigger flange to cover the hole. If you can send me some measurements on your current inlet I'd be happy to verify.
To seal your new inlet you'll want to use a bit of butyl tape # AL28FJ on the mounting... view full answer...
I am sorry but we do not have an AC cover with those dimensions. The closest option we have is the Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners item # AT3308046006 which measures 40-1/2" long x 29" wide x 7" tall.
If you could give me a part number off of your Dometic AC unit I can try to track down a replacement for it that way. Feel free to email me directly or add it in the comment box below. I hope to hear from you. view full answer...
Hi Loren,
Appreciate the info, and we do have a shroud/cover for your Coleman RVP air conditioner, with the correct part being the following:
- Replacement RV Air Conditioner Cover for MaxxAir Units - Coleman-Mach / RVP Brand # MA8335A5261
This cover measures 37" long, 25" wide, and 13-1/2" tall, so assuming the 35" you mentioned was the length and not the width, then this will fit for you. view full answer...
I took a look at the dimensions of your 2020 Aliner Expedition Camper. My information shows your camper measuring 18' long x 7-1/4' wide x 5-1/2' tall. With this in mind we are going to have to go with a cover not meant for a pop-up trailer like item # 290-12295 because of the height difference.
I recommend the Adco Olefin HD RV Cover for Travel Trailers up to 18' item # AD37ZR. This cover measures 18' 2" long x 8' 3" wide x 7' 6" tall. It has been built to survive in all climates and... view full answer...
Hello Ken. Do you happen to know what brand of air conditioner is on your 1997 Rexall Airbus? The cover in your picture does not look quite like anything we carry and knowing the brand and or model number would really help to narrow it down.
The dimensions you gave a very similar to the Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners # AT3308046006 which measures 40-1/2" long, 29" wide and 7" tall. The shape does not look the same though, so I am hesitant... view full answer...
I am sure we do but I do not have any way of knowing what size cutout your Fleetwood Southwind RV has so you'll need to take a measurement. The Dometic RV Refrigerator Roof Vent Cap and Base item # DMC97FR, you were looking at, is designed to fit a 23-3/4" long x 6-3/4" wide cutout hole. We also offer the Dometic item # DMC37FR which fits a 23-3/8" long x 6-1/2" wide cutout hole.
If these don't match up feel free to email me directly or comment below what size cutout your RV has so I... view full answer...
Hey Ken, we have verified in the pas that the Camco RV fridge vent cover part # CAM42163 works with the Atwood fridges like what you have and is black in color.
The Lippert steps part # LC432690 that you referenced would also work great as a replacement step setup as well. This matches the dimensions you need and would work great. view full answer...
For a 138-1/2" flange to flange measurement I recommend the Solera RV Slide-Out Awning - 139" Wide - Black # LCV000168328. This will have approximately 2-3/4" of overhang past the slide out so you'll want to make sure that there's enough clearance on both sides of the box. If not you can size down to the # LCV000184673 and would need to play with it a bit to get it centered on the box.
You'll want to pick up some butyl tape # AL28FJ to waterproof the mounting brackets as well. I've attached... view full answer...
I can verify that the depth of the portion of the # SR23VR that slips onto the flange is 1/2 inch as you can see it in the review video link that I attached. Hopefully that would still work for you as we don't have a version that has that portion of the wiper in a larger dimension. view full answer...
Go To Results